John Tetz Low Weight, Low Power E Ė ASSIST Recumbent Trike

Low Weight, Low Power E Ė ASSIST                      

Sept 2007 - By John Tetz

My assist philosophy has been based on the concept of truly low power giving just enough assistance.

This allows for a lighter weight system such that when the assist is not in use it doesnít detract from the overall efficiency of the vehicle/rider combination. This means the low assist weight requires very little additional energy from the rider when climbing or accelerating (a lightweight vehicle also helps).

My design goal was around 100 input watts to the motor and less than 10 pounds total system weight. It came in at 4.2 pounds, 1.9kg ! --† Thatís every thing Ė motor/gearbox/freewheel/mounting bracket assembly, battery, electronic controls.

The numbers (speeds and power) you will see throughout this report will be quite low for many HPV enthusiasts. But what I am designing for is not so much for speed but for reduced effort from the rider. Iím mainly designing for local alternate transportation and for more average people - people who simply donít have the power capabilities and need a little help. They would include smaller people, women, and us older folks. The rider pedals all the time but at a more comfortable level where both the rider and assist are combined and the power from each is somewhat similar. This fits with a definition of true assistance

MECHANICS
This shows the mounting bracket assembly (that would fit over a 2 inch, 50.8 mm, frame tubing). On the right is the motor. The motor is a TORCMAN Brushless Outrunner model TM 430-20. The motor is rated for far more than what I require but it does have a fairly low KVA, (RPM per volt rating which is around 500). The output of the motor goes thru a 19:1 gear box. On the left is a freewheel with a drive cog. Itís a cut down Shimano freewheel about ĺ inch, 19 mm  wide.

Click on the photos for a higher resolution image.


Total† weight,†† 2 pounds, 0.9 kg.

Modifying a standard freewheel is covered here

The freewheel article describes a left hand version but for this application a standard right hand drive is used (simpler to modify). In between are two support bearings for the freewheel plus a coupling to the gear box.

The system is pulling the chain coming off the bottom of the chain rings. This then allows use of the entire vehicle gearing with minimal change to the drive train. Because the drive is on the low tension side of the chain, the losses are very low when only human power is being used (maybe 1% or so).

There is a handlebar mounted push button to turn the motor on. With such low power there is no need for a throttle. Also by design, having to hold the button on encourages intermittent operation (also no power during shifting). The small battery also encourages intermittent operation (intermittent is key for a light weight system). I also have a small potentiometer that can be set for low to higher power (60 to 150 input watts). This helps tailor battery run times depending on terrain and length of trip.

This shows the motor assembly mounted below the leading edge of a seat. The black box sitting on the trike frame contains the electronics. There is an Electronic Speed Control (ESC) ( Castle Creations MAMBA Max ) to drive the motor with the proper series of pulses  - much like a stepping motor. This is a model aircraft/car ESC which normally requires a received signal from a transmitter.  That signal is generated by a small Astro Servo Tester.
Included in the box is a small auto relay (Radio Shack) to turn power on. I also have what is called a Flight Data Recorder (Eagle Tree). It records Pack Volts, Amps, Watts, RPM and Temperature which gives a detailed view of the operation, all on a downloadable plot (invaluable tiny piece of equipment). Instead of measuring motor RPM all the time I am measuring vehicle wheel RPM and on the plot it registers vehicle speed.

The battery is on the boom in front of the steering post. Its 9 NiMH Sub C† 4500 cells which weigh less than 2 pounds. I chose NiMH instead of LiIONs because LiIONs are still a bit finicky in terms of charging and discharging. I intend to charge the cells off a 10 watt roof mounted solar cell. I have a 5 watt cell charging my streamliner head light batteries and classic car battery. The choice of a 10.8† volt battery is so I can also charge off a car battery if Iím out on a trip (small regulator required).

Here is a view of the drive train side showing the additional idler to get decent chain wrap on the freewheel cog. Note that it is coaxial with the normal tension idler. This is a minimal change to the overall drive train.
PERFORMANCE
I know the following may be an overload of technical detail but put on your hip boots and wade in. Spend some time thinking about this because it is the key to how this system works.

To make more sense out of how power demands affect humans and how such a low power light weight assist system can help, a review of Human Power Capability is in order.

This plot shows the graph I used for a (Internal Combustion Engine) ICE Up-Hill assist talk that I gave at the 4th IHPVA Scientific Symposium in 1991.

The tested individuals would hold a specified power until such time they could not maintained that power any longer. The Healthy humans are students and military personnel (active young folks). First Class is self evident (amazing power isnít it) but note how steep that curve is. I added the Average Human curve representing us regular folks who are active but not in training. Our curve is also steep.† The steepness of the curve points to how sensitive human are to an increase in power demands. Tiny increases kill us. I used to be more or less on the line going down the center Ė but I wonder now 16 years later. But letís use the center line for this discussion. Using this plot as reference we can now look at what a low power assist can do.†

I did some tests on a 6.3% fairly linear grade of about 1450 feet, 442 M, in length and 100 feet, 30.5 M, altitude gain. With just human power I can do 4.2 mph, 6.8 kph,† which takes 127 watts (using a power calculating spreadsheet PDg on the HPVA web site). On the HP capability graph this would be around 1.5 hours to fatigue. With the assist at a low power setting the speed is 5.5 mph, 8.9 kph,† (30% increase) which the spreadsheet says is a total climbing power of 164 watts which if I had to do this would drop me into some number of minutes to fatigue. But with the assist which is delivering 50 watts to the wheel that reduces my power to 114 watts and ups my time to fatigue to 2.2 hours. 50 watts doesnít sound like much but this clearly shows how it doesnít take a lot of help to climb up that steep capability curve.

Yes Iím using a long term plot and that short term power does have the advantage of a recuperation period. But peak power slides deeper down the capability curve eventually adding up to fatigue. Just takes a little bit longer.†

On the road, that help is wonderfully noticeable in the reduced muscle effort along with reduced breathing and heart rates. I couldnít get Heart Rate data because the RF radiating from the motor/electronics blocked the heart rate pick up. When riding with other trikers that 1 MPH, 1.6 kph,† increase in climbing speed opens up quite a gap - I have to wait for them at the top of the hill and Iím much fresher.

EFFICIENCY
I ran some tests using only the assist on flat ground and up some grades. For flat ground the power to the motor is such that the vehicle is accelerating. That acceleration power has to be accounted for. On a steeper hill the speed can remained steady. I get numbers in the range from 50 to 55% efficiency. I have heard of similar numbers with hub systems (I would like to see more verification of this).††

BATTERY RUN TIME
I did some battery run time tests up the same 6.3% grade. Vehicle speeds/distances were collaborated on a bike computer and a separate datalogger (didnít have the RPM to vehicle speed worked out yet).† There are 8 runs up 1460 feet of distance and around 100 feet of altitude gain each run.

The first run was at the lowest pot setting on the handlebar which is around 100 input watts to the motor as described above.

The second run is at a higher input power setting and the speed is 6.5 mph, 10.4 kph,† and a total climbing power of 195 watts, 60 assist and 135 human power (HP). 195 would be way beyond my max power for any time/distance. With assistance I can put out a bit more power on occasions knowing that I wonít have to reserve myself for peak power demands later on the trip.††

Third run is same input power but slightly less HP. The speed dropped to 6.2 mph, 10† kph. Assist power 60, HP 127 watts. The other runs are variations on my input power until we get to the 7th run. Here the battery is starting to run down. The speed is slower at 5.8 mph, 9.3 kph. 173 total watts, with 50 assist and 123† HP.

The 8th run I had to shift down one gear and drop speed to 5.2 mph, 8.4 kph, with a total input power of 155 watts, assist 30, and HP 125.

Total battery run time 22 minutes. The Flight Recorder showed a 3800 MilliAmp Hour capacity used which is close enough to the advertised battery capacity (the battery was not totally drained). Quite acceptable for a 2 pound, 0.9 kg battery. And after 8 up hill runs I wasnít beat.††

However, since these runs I have learned a lot more about this type of battery and I should have limited the cut off to 7 runs. This can be done by setting the pack cut off voltage in the ESC.† I am collecting data and information on how to deal with these types of batteries and will probably write this up.

13 MILE TRIP WITH ASSIST USE TIMES
To see how often I would possibly use the assist I did a 13 mile, 21 km run over one of my test routes and used te assist quite a bit. The route has a total altitude gain of 690 feet, 210 M. Most are small grades in the 2 to 6% range. But there is a grade of 9.5% that is 792 feet long, 241 M.† The total trip time for the run was 69 minutes and total assist run time was 17.4 minutes or a 25% time use of assistance. Battery use was 2619 MAH out of a total 3800. I had around 6 more minutes of assist run time available which at 25% assist use would have been good for an hour and half trip.†

Letís review the operation on that 9.5% grade. Climbing with no assist the average speed was 3.8 mph, 6.1 kph. The SS says that is 162 watts or a time to fatigue for me at some number of minutes. I know the feeling of a heavy push on my legs, high heart and breathing rates. My HR monitor said I was up to 140 bpm which is getting up close to my red line.

The times from 25 sec to 37 seconds are down shifts. The steepest part of the hill is from 40 seconds to 136 seconds. With assistance the speed is 4.4 mph, 7.1 kph, (Purple). That speed dip at 57 to 72 seconds is a drop out from the speed pickup not the vehicle. Havenít been able to figure out why this is happening.† Motor input power 130 watts (Orange) or 65 watts to the wheel. The PDg spreadsheet says 188 watts is needed to climb this hill, so that translates to 123 watts HP which means the time to fatigue jumps from minutes to 1.5 hours.†


Plot 3 - With Assistance

ACCELERATION HELP
Acceleration is another power demand on the rider. Although itís a short length of time the increase in watts is significant. And it happens over and over during a trip - each time, the rider dips into their reserves.
†This plot shows a HP Acceleration test with no assistance on fairly flat ground.

I use the section of curve from 9 mph, 14.5 kph, to 15 mph, 21.1 kph. At 9 mph steady state, the PDg† spreadsheet† says it takes 32 watts.† Going from 9 mph to 15 mph in 15.5 seconds equals 0.39 mph/sec acceleration rate. The SS then shows the power to be 100 watts. 32 to 100 watt increase is a big percentage change.

This plot shows HP acceleration with assist help thru 2nd† thu 4th gears†during the same 9 to 15 mph, but in 10.2 seconds.

This gives 0.59 mph/sec acceleration or a power of 134 watts. The assist delivers 55 watts to the wheel.† The HP turns out to be 79 watts. I tried to pedal at the same effort that I used for the non assist run but it appears that I didnít do that. 79 watts is a lot less than the 134 that would have been required.†

The speed does not increase after 414 seconds because there is about a .26 % grade.† That grade costs 130 watts of sustaining power at 15 mph, 24.1 kph, so thatís subtracted from the acceleration power which drops the acceleration down to around zero. You will note the power to the motor climbed at the 422 second location after I shifted into 7th gear but is so short that there is no apparent acceleration. At 430 seconds there does show some acceleration and that also coincides with the grade leveling off. Another input variable is I might have changed my HP seeing I was close to the end of the run.† With all these variables these plots are simply to show approximations of the kinds of power required.†

I use the assist quite often thru the gears to get up to speed when I do my errands. These are generally 4 to 8† second motor runs. The feeling of getting acceleration help is terrific and a bit addictive. Because I havenít used extra power to accelerate I am fresher so I can maintain the cruising speed a bit longer† If the sustaining power required is too high and the speed begins to fall off I push the button and within a number of seconds climb back up to speed. Or if there is a short terrain rise I push the button to maintain speed over that rise.


Tetz Zotefoam Velomobile

Meanwhile all thru this operation my body is only producing the sustaining amount of power. Knowing you donít have to produce acceleration power can translate into increasing the cruising power a bit so cruising speed can change from 15 mph, 24.1 kph† (84 sustaining watts) to around 17mph, 27.4 kph (110 watts). The same two wattage values give 17† and† 20 mph, 32.2 kph. with my Velomobile.

Assistance is not as noticeable at high speeds particularly if acceleration is needed because the amount of total power required is high and the assist percentage is low. But I find that speeds up to the low 20 mph, 32.2 kph, range fits well with human capability and assist power. The assist simply takes the peak demands off the rider.

EXTRAS
Some people may not like the chain drive system pulling the feet around. With such low power this pull from the assist is so small that itís not annoying. You quickly learn to be pedaling before hitting the button. You need to be pedaling otherwise there may be some short but high current spikes in the 60 amp range if engaging the assist too early. These current spikes do nothing for acceleration but put a high demand on the battery.†

Some chain drive assist systems have a freewheel on the cranks so the rider doesnít have to pedal when the assist is on. That may be ok for a higher power assist (higher weight), but when the assist is in the order of 50 watts to the wheel thatís not enough to get the weight of the vehicle and rider going. If the rider pedals all the time the HP is low, the assist power and weight of the system can be considerably lower adding up to an elegant high bike/human efficiency.

I could have included a circuit that sees if the chain rings are turning properly which could then send a signal to the electronics to turn on the motor. I didnít do this because I already have a very sophisticated computer on board. It knows when to turn on the motor plus it can anticipate needs depending on the up coming shape of the terrain. It knows when to shift gears, and it can pre-estimate how much assist to use on a longer trip depending on what kind of assistance will be needed overall. And this computer is packaged in a fairly small space. That computer is called the human brain. Hard to beat.

FINAL COMMENTS
This has turned out to be a fun project. I had the idea of seeing how small and light an electrical assist could be made some time ago (influenced by my ICE assist experience many years ago). Once I had done enough research on motor gearbox possibilities the concept of the co-axial layout fell into place. And it was a pleasant surprise that the system does exactly what I want it to do.

As for the heavier vehicles (and riders) I can see increasing the power to the motor from my nominal of 100 watts to say around 150 watts nominal. This of course may require a bigger battery pack.† Nine C cells would add around 0.5 pounds, 0.3 kg. Or maybe D cells would be even better which would be more like 3 pounds 1.4 kg† total pack weight - a little less than double the weight of my pack.

I also would be a little concerned with constantly pushing high power thru the tiny gear box (above the 150 watts). Donít know the reliability as yet. I have only had this system running since July 07. By asking for more power quickly adds weight. Conversely 4.2 pounds may be the lowest practical weight of an E-system.

I do wish the noise coming from the Motor/gearbox was lower - canít sneak up on someone. I tried wrapping the gearbox in rubber but the torque is so high that the aluminum cover clamp (in the photo) has to be so tight that the noise reduction is minimal. I had to make a torque limiter bracket on the motor/gearbox because it would slowly crepe around (it has three electrical leads). A slower rotating motor would reduce the gear box ratio but the game here is the motor efficiency may fall off faster than the gain from less gear reduction. Slower turning motors also often mean larger diameter and may result in difficulty fitting it in tight spaces on a bike/trike (like under the seat in my case).

One concern I do have is normally on my short 5 to 10 mile, 8 to 16† km errand runs I purposely do strong HP acceleration out of intersections and stop streets as a way to do mini interval training. If I use the assist for acceleration help, it is thrilling but in the long run I may be loosing muscle tone.†

Comparing ICE to E-assist, the range on the ICE is fantastic and is terrific for long distance tours where-as the E technology canít compete (within similar weights).† But the ICE system cannot be turned on/off instantly so the E system has a greater advantage for local alternate transportation needs.

Even though the 4 pound, 1.8 kg, E weight can be felt (with and without that weight Ė (noticed mainly during acceleration) itís a rather small reduction in human/bike efficiency in exchange for a pleasant amount of help when needed.

John tweaks this system on the Current Limiter and Transient Spike Reduction pages

Contact master builder John Tetz at jgtetz $AT$ msn.com

More about John's project and others on the ULEA (Ultra Light Electric Assist) Yahoo Group

 

      Back to the HPV projects